Wednesday, July 25, 2012

Airbrushing Part 1 - Basics

One of the most popular requests I get these days hobby wise is airbrushing advice.  Here's an attempt to compile my thoughts and experiences thus far.  This is more appropriate for those who learn better by doing things hands-on like me.  A lot of this has been trial and error as I haven't sat down with any videos or classes since college 13 years ago.

I'll start with my airbrushing station as preparation and tools are very important.




Here's my station in my hobby corner.  Well ventilated with several open windows and fans.  The paint can on the left has several magnets stuck to it which I use to hold models since I put washers on the bases also.  Water with a dropper/turkey baster in the middle.  The compressor on the right is new and pretty nice and quiet.  Paper towels for cleaning the airbrush.  The foam core in the back is for catching over spray and test firing my paint and pressure.


Mastering your pressure and paint/water mix is key to not ruining your models.  I currently paint at about 18psi and water my paints down to "heavy cream" since I use cheap acrylics not meant for airbrushing.  Too much water or pressure will make the paint "spider" as seen above (bad).  Proper pressure and dilution will allow you to paint in broad strokes or fine lines (good).

Washing out your airbrush is also key.  I can usually paint for about 5 minutes straight before flushing the brush with water.  I disassemble the unit and fully clean it between colors.

My main use for airbrushing is to provide a dynamic base coat to paint over with a brush.  It's important to not attempt too much with an airbrush (IMO).  Let me also say that my techniques are focused on saving time and money first.  These aren't techniques that will win you painting awards, but they'll get new units and armies on the table quickly.  I'll start with the new tyranid scheme which has very little airbrushing and will be an easier place to start.


Here's 3 bonesword warriors and an alpha warrior primed white.


First, I airbrushed Grass Green (FolkArt) on the base and tip of the swords and on their finger.  These models are fully assembled as I was painting over my old green/black scheme.  When airbrushing assembled models, it's important to hold them so you are spraying the needed part only and not onto the rest of the model.  Sometimes you can do this by changing how you hold the model, sometimes you need a paper towel for a mask. 


All swords and fingers finished with Apple Orchard.  About 10 minutes in at this point for 2 colors and cleaning.


Next I even out the armor plates with Wicker White over the primer.


Then Ivory White down the center of the armor plates leaving only the outer edges.  At this point my old compressor died so I went out to Harbor Freight and got the new (better) compressor pictured above.  In the meantime, I applied a Violet Purple wash to the flesh over the primer.


I also applied an Apple Orchard wash to the guns.  The washes for this phase are applied by brush and are VERY watered down.  I want the washes to flow off the high points and settle into the details.


Back to airbrushing with my new compressor, I applied Tapioca down the center of the armor plates leaving more of the edge exposed than the last layer.  At this level of precision, I test fire the airbrush on the paint can and on my hand before applying paint to the models.  This way you minimize the potential for mistakes.


As a final airbrush coat, I use Honeycomb down the middle of the armor plates.  This is pretty much a narrow line, leaving more exposed from all previous layers.  This is where I switch over to washes and detailing.  The airbrushing is just a basecoat to detail over.  About 3 hours in at this point for the whole batch between airbrushing and washes.


Here you can see where I picked one model (front center) to finish as a test model.


Additional washes of Thunder Blue were applied over the purple skin to settle in the details.  A black wash was finally applied to the joints, gills, and creases.  Grass Green was washed over the Apple Green gun.  Armor plates were detailed with Pure Black, Dark Brown, and Honeycomb from a very wet palette.  The paint applied is more of a stain to the undercoat and more resembles a wash than a "layer" of paint.


Here's the carnifex using the same process.


 A small 1,000pt force in progress.  This represents about 2 weeks worth of free time if I get 2 hours a day.  Not a ton of airbrushing, but it can be limiting if you're painting fully assembled models and want to use different colors.

Part 2 of this series will focus on blending base coats and focus on the dark eldar which have much more airbrushing.  Part 3 will be directional lighting with the grey knights and maybe a sneak peek of my current project.  Part 4 will be airbrushing bases.



14 comments:

  1. Nice post! This is the sort of thing I'd like to see more of. So far I've only used the airbrush for basecoats, so I'd like to expand my techniques

    ReplyDelete
  2. Great post! I'm just starting to use my airbrush consistently and it has been a really excellent time saver. I have only used it on vehecles, so far. Not sure how to move forward with troops but your post has helped me with that. Thanks!

    ReplyDelete
    Replies
    1. Thanks man. I need to order one of your tentacle kits one of these days for my tyranid aegis defense line.

      Delete
  3. Ok, gotta ask the n00b questions as I've been debating getting an airbrush for sometime :-)

    What airbrush and compressor do you use? Pro's and Con's? Any advice on choosing a particular setup?

    Thanks for the article, love the advice!

    ReplyDelete
    Replies
    1. Here's a site I found when researching for mine:

      https://sites.google.com/site/donsairbrushtips/

      I ended up buying the Paasche Talon. From a very reliable seller on eBay I got the airbrush, accessories and compressor for $200 plus shipping.

      Delete
  4. Great! I'm one short step from using airbrush so I'll take this to my "favourites" to reread a bit later:)

    ReplyDelete
  5. The new nids look really nice, man. I've been thinking about buying a new airbrush that can produce a finer spray. Mine is really only good for base coating my tanks, which saves me lots of time and gives a great finish. Any suggestions? What do you use?

    ReplyDelete
  6. I use a Badger Anthem airbrush for no other reason that it was the "best" one Michael's had and they usually have a printable coupon for 40% off. Getting a dual action airbrush is important, but IDK about all the extras. I've never had my hands on an expensive airbrush to compare mine to. FWIW I use a $30 central pneumatic airbrush at work and I bet it's just as good as mine.

    The compressor I use is also a Central Pneumatic product. You can see it in the first pic. It's about $90 at Harbor Freight which also has printable coupons.

    ReplyDelete
    Replies
    1. I've heard good things about Badger. It's the only brand the hobby shop near me has. Just wasn't sure what the difference between the $70 and $200 models really could be.

      Delete
  7. Thanks for this.. I've been experimenting with airbrushing to some limited success..mainly as base coats.. it's useful to know the ins and outs from someone who clearly knows what they are doing.
    Look forward to the next posts.
    Ven

    ReplyDelete
  8. I liked this post alot, it gave me some nice pointers. Turnes out i also prefer around 18psi with slightly thinned out vallejo model Air paints :) Thanks for the post, cant wait to see the DE post, since i want to do the same just with other colours ^^

    ReplyDelete
  9. Could you talk a bit about how you thin your paints and what PSI settings you use?

    ReplyDelete
    Replies
    1. Right now I paint at about 18-20 PSI.

      Thinning down the paints can be tricky, probably because I use cheap paints not meant to be used for airbrushing. FolkArt paints tend to come off the shelf with the consistency of toothpaste. I typically squeeze out 25%-33% of the bottle into the garbage and replace that much volume with water and shake vigorously. That usually gives me a viscosity to get clean drops of paint from the bottle. At that point, I usually use about 3 drops of paint to 1 drop water mixed directly into the airbrushing pot and stir well with a sucker stick.

      Delete
  10. Hi, Could you comment a bit more on how you finished off the armor plates? I am very interested in this color scheme as it really pops! I'm rather new to painting and airbrushing so it will all be a big learning curve :)

    Cheers,
    Mitch

    ReplyDelete